2000 Toyota Tundra Rear Axle Removal

Wednesday, May 26, 2021 Edit

How to remove front and rear bumper Toyota Tundra 2000-2006 English. SAVE THE ABS- Save the ABS Sensor ring and remove the bearing from the axle.

2000 Toyota Tundra Rear End Axle Bearing Replacement 2 Wheel Drive

Dec 20 2011 Edited Took my 08 Tundra 2wd to a local shop that specializes in trucks so they can replace the rear axle bearing.

2000 toyota tundra rear axle removal. I went up there to check it out. 21122011 Discussion Starter. Parts fit for the following vehicle options.

After the axle is removed disconnect the service tool. 10Loosen the brake line. A special service tool SST part number 09521-25011 will be needed to remove the rear axle shaft and bearing retainer from the backing plate.

11Pull the axle shaft out and set it aside. With 328900 miles on all original engine and drivetrain The rear differential has started to display fatal problems and needs replacement. For additional information refer to Axle Shaft in this section.

Remove the axle from the press as well as the Axle Bearing Puller tool. Forget about a hammer chisel and your torch. EASY TO USE-This bearing puller tool is easy to use.

Differential are shipped directly from authorized Toyota dealers and backed by the manufacturers warranty. Parts like Rear Axle Housing. Place a drain pan under the end of the tube to catch any gear oil which may drip.

12Put a vacuum cap or something over the end of the brake line to prevent spillage. The Yukon axle bearing Puller can be used with a press or with the Yukon carrier bearing Puller and an air-gun to safely and quickly remove bearings. Remove the inner oil seal.

Remove the axle shaft. Have our technicians examine your 2000 Toyota Tundra. Lastly tap the rear of the hub assembly with a rubber mallet and it will release from the axle tube.

STURDY- Our Rear Axle Shaft Bearing Puller is made premium material that is highly durable for long term use. Use a paper towel under it to catch spills for now. This retainer will become your outer retainer on re-assembly.

Remove the captured ABS tone ring and inner retainer. Make sure to check inside the axle tubes for any damage debris or abnormalities. They cant seem to get the bearing and housing to bust loose from the axle.

To replace a rear axle seal or bearing the rear axle should be placed securely on jackstands and the tire removed. Cutting a bearing off an axle can damage the axle and is potentially dangerous. Remove the axle shaft 4234.

They had rigged something to the hydraulic press and put some unbelievable. Press Axle Out of Outer Retainer. 6 Cyl 34L 8 Cyl 47L.

Using the special tools remove the rear wheel bearing and wheel bearing oil seal. Pull the complete axle assembly from the axle tube with caution. 14mm wrench Second remove the 2 brake lines from the drums.

Remove the axle shaft from the backing plate. 22122012 First jack rear end up and block itRemove the rear tiresTake off caliper and caliper bracketNext remove the rotorThen there will be a big nut in the center that the axle is bolted toRemove that nutThen make sure thees no wires for abs or any other kind of wires connected to the bearingNext you should see 3 bolts holding the bearing in maybe 4 they changed them so many timesAfter removing. 30122009 First remove the 4 bolts from the driveshaft and lift it up and secure it with the bungee cord.

The Yukon axle bearing Puller safely removes pressed on axle bearings for a variety of applications. With this tool it is a breeze. OE replacement axles are made of forged alloy for a 20-30 percent increase in strength over their stock counterparts.

07122018 AC Climate Control Knob - Set of 3 - Replaces 55905-0C010 559050C010 - Compatible with Toyota Tundra 2000 2001 2002 2003 2004 2005 2006 - Air Conditioner Replacement Switch 1499 Oznium Brightest Light Bolt - Flush Mount 12V LED Light for Bumper Grille Cars Interior Dash Ambient Lighting Motorcycle wSleek Aluminum Housing. 10 mm wrench Third remove the drain and fill plugs from the axle and let the fluid drain out into a container for proper disposal. If the wheel bearing oil seal is leaking the axle housing vent may be plugged.

11022015 2000 Toyota Tundra rear end axle bearing replacement 2 wheel drive V8 without ABS. Remove the 4 nuts securing the Axle Bearing Puller tool to the red ABS tone ring capture plate. Series Axle 2000 Front Passenger Side Axle Shaft by Nitro Gear.

If youre hearing gear whine clunking or bearing noise from your rear differential it may be necessary to remove it and have it rebuilt. 13062012 I have a 2000 Tundra 4x4 w 47 v8. Make sure to remove and replace the rubber seal.

Remove the rear axle bearing. Schemes of fastening of front and rear bumpers. Differential - Repair or Replace.

-----Rear Wheel Bearing and Axle Shaft Oil Seal Removal. 08112009 9Remove the 4 14mm nuts that hold the axle shaft to the housing. The lines are directly above the axle.

Toyota Tundra SR5 with Toyota 80. 13Remove the rear speed sensor. Remove the outer oil seal.

The rear end is the 390.

Axt34040

R C Tractor Trailer Truck Rear Axle Suspension For 1 14 Tractor Trailer Truck Container Truck Tractor Trailers

Replace 05 Toyota Tundra Rear Axle Shaft Wheel Bearing And Seals Without Shop Press Youtube

Plasti Dipped Mirrors Sr5 Trim Removed From Wheel Wells 2003 Toyota Tundra Toyota Tundra Toyota Trucks

Rear Axle Seals Bearings Toyota Tundra Forum

Pin On Trucks

Rear Axle Shaft Bearing Toyota Sequoia 2001 Repair

Pin On Tundra 1st Gen

Toyota Tundra Inner Axle Shaft Seal Youtube

Rear Axle For 2000 Toyota Tundra Toyota Parts Center

New Grille And Plasti Dipped Bumper Lip Toyota Tundra 2004 Toyota Tundra Toyota Trucks

Pin On Trucks

Rear Axle Seals The Ultimate Information And Replacement Thread 3rd Gen Toyota 4runner Forum Largest 4runner Forum 4runner 4runner Forum Toyota 4runner